Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR Repair Manual Download Page 60

Page: 60 / 109

- A13 ・ AF-S 28-300mm f/3.5-5.6G ED VR -

JAA80851-R.3811.A

#154

#179×3

#156

#154

#34

B31×9

May.10.2012

•

Attach the roller (#156).

•

Put the two rollers (#154) at the below reference position.

•

Tighten the three screws (#119).

•

Tighten the three screws (#179) with the torque driver (J15420).

Reference position

•

Mount the nine blades (B31) on the blade mounting ring (#34).

Aperture unit

Eccentric roller

Non-eccentric roller

(Torque value: 15 cN.m)

△ (

Addition)

Changed page

△

× 2

△ (

Revision)

Tightening torque= 15 cN

・

User ID:uncf8224

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR














































































































Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands

Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR, Repair Manual

Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands