Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR Repair Manual Download Page 67

Page: 67 / 109

- A20 ・ AF-S 28-300mm f/3.5-5.6G ED VR -

JAA80851-R.3811.A

#1008

#95

#175×2

EDB0011

#95

#149

#150

Fold back and

attach [#1008].

Attach the pieces of the tape (#149 and #150) [only when the pieces of the tape (#149 and #150) were

removed for replacement].

Attach the VR FPC (#1008) to these pieces of the tape (#149 and #150).

•

Reference position

for attachment

Insert the end of [#95] in the hole.

Mount the retainer plate (#95).
Tighten the two screws (#175).

•
•

Retainer plate

User ID:uncf8224

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR














































































































Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands

Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR, Repair Manual

Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands