Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR Repair Manual Download Page 32

Page: 32 / 109

- D28 ・ AF-S 28-300mm f/3.5-5.6G ED VR -

JAA80851-R.3811.A

#1008

B147 (A-D)×3

#148 (A-I)×3

#1008

Peel off the VR FPC (#1008).

•

Peel off [#1008] and pass it

through the hole towards the

inside.

Remove the three rollers (#148: A-I) and three straight keys (B147).

Note: The size of the roller (#148) differs depending on the cam groo�e width of the cam ring (#24),

The size of the roller (#148) differs depending on the cam groo�e width of the cam ring (#24),

while that of the roller (B147) differs depending on the straight groo�e width of the fixed tube
unit (B50). Therefore, if [#24]

B50] is NOT replaced (with a different new one), make an

identification mark, etc, to identify which roller used to be attached to which location.

•

Fixed tube unit

User ID:uncf8224

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR














































































































Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands

Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR, Repair Manual

Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands