Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR Repair Manual Download Page 48

Page: 48 / 109

- A1 ・ AF-S 28-300mm f/3.5-5.6G ED VR -

JAA80851-R.3811.A

#52

#53

MZ-400EL

F890

TA-0012 (5×9)

MZ-400EL

Reference position for attachment

Apply to the 3 cam

grooves of [#52].

Apply the grease (MZ-400EL and F890) to the 2nd lens-G straight ring (#52).
Attach the tape [TA-0012 (5×9)] [only when the tape (TA-0012: 5×9) was removed for replacement (with
a new one).]

•
•

Assembly

Apply to " "

area.

Apply the grease (MZ-400EL) to the 2nd lens-G rotatory ring (#53).

•

2nd lens-G rotatory ring/2nd lens-G straight ring

Assembly of 2nd lens-G straight ring unit

Apply to the three cam grooves of [#53]

and inner circumferential groove, and

U-shape groove.

User ID:uncf8224

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR














































































































Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands

Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR, Repair Manual

Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands