Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR Repair Manual Download Page 81

Page: 81 / 109

- A34 ・ AF-S 28-300mm f/3.5-5.6G ED VR -

JAA80851-R.3811.A

#91×2

EDB0011

Standard: Amplitude of all pulses/waveforms is 200mV or more.

Caution: Check the wa�eform by rotating the MF ring (#26) all the way around back and forth.

If there is no problem with the waveform of GMR sensor, apply the adhesive to the head of the two

screws (#91) to fix.

If the amplitude of the waveform is less than 200mV, bend the head of the GMR sensor and make the
adjustment. Then, check the amplitude again.

•

3. How to inspect and adjust:

Confirm that the voltage of the connected rated voltage power-supply are set values (5.0V), then turn it

ON.

Set the oscilloscope, and turn the MF ring (#26) by hand.

In case large waveform-noise is detected, use the FILTER function.

How to set FILTER function (e.g. DL1540 manufactured by YOKOGAWA)

①

Press the FILTER button.

②

Select "Smooth" of the menu on screen and turn it ON.

•

Oscilloscope setting

V/Div(ch1)

100mV

V/Div(ch2)

100mV

Coupling

Time/Div

1ms/div

Trigger Mode

NORMAL

Trigger Coupling

Trigger Source

CH1

Trigger Position

+4div

Trigger Type

EDGE

Trigger Level

INPUT(ch1)

INPUT(ch2)

User ID:uncf8224

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR














































































































Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands

Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR, Repair Manual

Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands