Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR Repair Manual Download Page 51

Page: 51 / 109

- A4 ・ AF-S 28-300mm f/3.5-5.6G ED VR -

JAA80851-R.3811.A

B51

#25

F890

#38

MZ-400EL

GN-20S

#52

Mount the 1st lens-G cam rign (#38).

•

Apply to the 3

cam grooves.

Mount the focus cam ring (#25) and 2nd lens-G movable ring unit (B51).

•

Mount [#25] so that its straight groove

is positioned as above.

Align these U-shape grooves.

Apply to the

cam/straight

grooves.

1st lens-G cam ring

Focus cam ring

Mount [#38]. Then hold the legs of
[#52] and turn in the direction of

the arrow for assembly.

There is no difference

between the top and

bottom sides.

User ID:uncf8224

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR














































































































Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands

Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR, Repair Manual

Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands