Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR Repair Manual Download Page 99

Page: 99 / 109

- A52 ・ AF-S 28-300mm f/3.5-5.6G ED VR -

JAA80851-R.3811.A

B1007

#117×2

①

②

4. By following the procedure from 1 to 2, check that the A-contact pin position is within standard.

5. Check whether the position of the other pins than A-contact pin meets the standard or not.

If the A-contact pin position meets the standard but other contact pins do not, bending or looseness of the

contact pins is possible.

3. Take out the two screws (#117) from the contact unit (B1007), and position the contact pin section to

meet the standard. Tighten the two screws (#180) in the numeric order from

①

②

User ID:uncf8224

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR














































































































Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands

Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR, Repair Manual

Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands