Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR Repair Manual Download Page 98

Page: 98 / 109

- A51 ・ AF-S 28-300mm f/3.5-5.6G ED VR -

JAA80851-R.3811.A

J11360

Cross line of gauge

Contact pin

Standard position of contact pin:

In relation to the cross lines, the apex of the contact pin must be positioned as below.

Within one-fourth of diameter sideways from the intersecting point.

Caution: To confirm the position of the contact pin, look straight at the each contact pin

horizontally from an anterior view.

A-contact pin

2. Check whether the position of the A-contact pin meets the standard or not.

In case the result meets the standard, go to the procedure 5.
In case the result is out of standard, go to the next procedure and adjust it.

Lock hole of bayonet

mount unit

Reference pin

Inspection of AF-contact pin position

Whenever the contact unit is removed, be sure to make this AF-contact pin inspection.

1. Mount the inspection tool (J11360) on the bayonet mount unit by fitting the reference pin of [J11360] in

the lock hole of the bayonet mount unit.

User ID:uncf8224

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR














































































































Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands

Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR, Repair Manual

Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands