Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR Repair Manual Download Page 49

Page: 49 / 109

- A2 ・ AF-S 28-300mm f/3.5-5.6G ED VR -

JAA80851-R.3811.A

ﾏｳﾝﾄ側

#102×3

#103 (A-G)×3

#52

#53

TA-0004 (2×4)

#114×2

#114

L-241

May.10.2012

Apply

to the

threaded

portion.

•

Turn the 2nd lens-G rotatory ring (#53) until the three screw holes can be seen.

•

Attach the three rollers (#103: selected from A to G) and three screws (#102).

•

Tighten the three screws (#102) with the torque driver (J15420).

Note: Select the appropriate roller (#103) depending on the inner circumferential groove width of

the rotatory ring (#53). (ref. page D4)

•

Attach the two double stick tape (TA0004 [2×4]) to the two plate springs (#114).

•

Attach the two plate springs (#114).

•

Mount the 2nd lens-G rotatory ring (#53).

Backside

Mount [#114] so that the attached tape (TA-0004)
is positioned to the right side when viewed from
the back of [#114].

Changed page

△

× 2

(Torque value: 15 cN.m)

△ (

Addition)

Tightening torque= 15 cN

・

△ (

Revision)

User ID:uncf8224

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR














































































































Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands

Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR, Repair Manual

Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands