Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR Repair Manual Download Page 88

Page: 88 / 109

- A41 ・ AF-S 28-300mm f/3.5-5.6G ED VR -

JAA80851-R.3811.A

J18004-1

EDB0011

#117×2

Lock pin

Lock hole

Screw × 2

Aperture lever

If the aperture blades open quickly or slowly, adjust the position of aperture lever with two screws.

After the adjustment, apply [EDB0011] to the two screws.

•

Aperture lever adjustment

Set the zoom ring to TELE-end.

Take out the two screws (#117).
When the lock pin of [J18004-1] is put into the lock hole of bayonet, confirm that the aperture blades

become fully open.

Tighten the two screws (#117).

•
•
•

•

User ID:uncf8224

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR














































































































Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands

Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR, Repair Manual

Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands