Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR Repair Manual Download Page 54

Page: 54 / 109

- A7 ・ AF-S 28-300mm f/3.5-5.6G ED VR -

JAA80851-R.3811.A

B2040

MZ-400EL

MZ-2252EL

B2040

Apply to the magnetic

tape area.

Apply the grease (MZ-400EL) to the gear unit (B2040).
Apply the grease (MZ-2252EL) to the magnetic tape area of the gear unit (B2040).

•
•

Gear unit

Mount the gear unit (B2040) and align "∞" position with the indexes as below.

•

Check that the hole for the infinity mark

of [B2040] is aligned with the hole of

the fixed ring unit.

Fixed ring unit

Apply to " " area.

User ID:uncf8224

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR














































































































Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands

Nikon AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR, Repair Manual

Search results

Summary of Contents for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Reviews:

Related manuals for AF-S NIKKOR 28-300mm f/3.5-5.6G ED VR

Brands by name

Popular brands