Nidek Medical LE-9000DX Express, Operator'S Manual

Page: 93 / 153

5 - 4
11) Layout memory : None, Exec
Factory setting: Exec
This is for selecting whether or not to call up layout data as well as the lens shape when
calling up the data with the memory function.
In the following screen, data in the area shows that it can be called up to the screen
at each setting.
<When setting at “None”> <When setting at “Exec”>
12) Bar Code memory : None, Exec
Factory setting: None
This is for selecting whether or not to use the optional barcode scanner to call up the data
from the internal memory. By connecting the barcode scanner, it becomes possible to
store 500 pieces of frame data.
13) Half eye check : None, Exec
Factory setting: Exec
This is for selecting whether or not to display the message suggesting cup replacement
and to stop the instrument, during processing of a lens with a short vertical width.
Set the parameter to “Exec” except when the half-eye lens chucking is successively
performed.
14) Data Transfer : NON, VALUE, MATER, POLIS, BF, ALL
Factory setting: NON
This is for selecting the kinds of data that the edger does not accept when receiving data
from an external device. The selected data in the parameter will be transmitted, but not
accepted by the edger. On the edger side, the previous data remains active even after
data transmission.
Only when the communication specifications are special and the parameter “Ext. inter-
face” is set to “DVI”, this setting is available.
NON:
No received data will be disabled; All the data will be recognized and shown
on the screen.
VALUE: All the data of the lens layout is disabled.
MATER: The data of lens material is disabled.
POLIS: Only the data of “POL (polishing)” is disabled.
BF:
Only the data of “BIF (bifocal) mode” is disabled.
ALL: All the data of the lens layout and processing conditions are disabled.
15) BF ChuckLayout Side : ± mm
(If a minus value is input, the lens will be processed with its blocked point at the speci-
fied value outside from the top line center of the segment.)
Factory setting: – 5 [mm]
㧹㧵㧺ޓޓ㧢㧡
㧚ޓ
㧚ޓ
ޓ㧚
㧚ޓ
㧲㧼㧰㧦㧢㧥㧜㧜ޓޓޓޓޓޓޓޓ 㧲㧼㧰㧦㧢㧥㧜㧜ޓޓޓޓޓޓޓޓ
㧼㧰 㧼㧰 ޓ㧦㧢㧞㧜㧜ޓޓޓޓޓޓޓޓ ޓ㧦㧢㧞㧜㧜ޓޓޓޓޓޓޓޓ
ޓޓޓ㧦ޓޓ㧞㧜ޓޓޓޓޓޓޓޓ ޓޓޓ㧦ޓޓ㧞㧜ޓޓޓޓޓޓޓޓ
㧿㧵㨆㧦ޓ㧜㧞㧜ޓޓޓޓޓޓޓޓ 㧿㧵㨆㧦ޓ㧜㧞㧜ޓޓޓޓޓޓޓޓ
㧭㧯㨀ޓޓޓޓޓޓޓޓޓޓޓޓޓ 㧭㧯㨀ޓޓޓޓޓޓޓޓޓޓޓޓޓ
㧹㧱㧹 㧹㧱㧹㧦ޓ㧝㧜㧜ޓޓޓޓޓޓޓޓ 㧦ޓ㧝㧜㧜ޓޓޓޓޓޓޓޓ
㧼㧸㧭 㧼㧸㧭㧺㨅㧸㧭㨁㨀㧼㧻㧸ޓޓ 㧺㨅㧸㧭㨁㨀㧼㧻㧸ޓޓ㧾
㧚ޓ
㧚ޓ
ޓ㧚
㧚ޓ
㧹㧵㧺ޓޓ㧢㧡
㧲㧼㧰㧦㧢㧥㧜㧜ޓޓޓޓޓޓޓޓ 㧲㧼㧰㧦㧢㧥㧜㧜ޓޓޓޓޓޓޓޓ
㧼㧰 㧼㧰 ޓ㧦㧢㧞㧜㧜ޓޓޓޓޓޓޓޓ ޓ㧦㧢㧞㧜㧜ޓޓޓޓޓޓޓޓ
ޓޓޓ㧦ޓޓ㧞㧜ޓޓޓޓޓޓޓޓ ޓޓޓ㧦ޓޓ㧞㧜ޓޓޓޓޓޓޓޓ
㧿㧵㨆㧦ޓ㧜㧞㧜ޓޓޓޓޓޓޓޓ 㧿㧵㨆㧦ޓ㧜㧞㧜ޓޓޓޓޓޓޓޓ
㧭㧯㨀ޓޓޓޓޓޓޓޓޓޓޓޓޓ 㧭㧯㨀ޓޓޓޓޓޓޓޓޓޓޓޓޓ
㧹㧱㧹 㧹㧱㧹㧦ޓ㧝㧜㧜ޓޓޓޓޓޓޓޓ 㧦ޓ㧝㧜㧜ޓޓޓޓޓޓޓޓ
㧼㧸㧭 㧼㧸㧭㧺㨅㧸㧭㨁㨀㧼㧻㧸ޓޓ 㧺㨅㧸㧭㨁㨀㧼㧻㧸ޓޓ㧾