Nidek Medical LE-9000DX Express, Operator'S Manual

Page: 122 / 153

8 - 21
4. Go back to the MENU screen.
Press .
5. Go back to the Layout screen.
Press twice.
6. Repeat Steps 1 - 5 until the whole edge is polished evenly.*
1
7. Check the finished size after polishing.
Check each material lens for beveling and flat edging (only flat edging with Type PL4).
1) Call up the
φ
45 built-in data.
Press while pressing on the
Layout screen.
2) Perform polishing of beveling and flat
edging.
Leave the Size indication at 0.
3) Check the finished size.
If the processed lens diameter is as follows,
it is proper.
Beveled lens: 45.00 - 45.10 mm (dia.)
Flat edged lens: 45.00 - 45.10 mm (dia.)
8. If the finished lens size is too large or too small, adjust the polishing size.
1) Call up the MENU screen.
Press .
2) Call up the Size adjustment screen.
Align the pointer (
→
) to “Size adjustment”
and press .
*1 If the lens edge is not polished completely even though the constant value was adjusted, the
axis angle may have shifted while the edge was being polished. In such a case, input the
compensation value indicated at “POL AXS const. (bevel)” or “POL AXS const. (flat)” as
described in “8.11.3 Axis shift adjustment for polished lenses” (p.8-24).
㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖
㧖ޓޓޓޓޓޓޓ㧿㨕㨦㨑ޓ㨍㨐㨖㨡㨟㨠㨙㨑㨚㨠ޓޓޓޓޓޓޓޓ㧖
㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖㧖
ޓޓޓޓޓޓޓޓޓޓޓ㧖㧱㨄㧵㨀ޓ㧦ޓ㧼㨞㨑㨟㨟ޓ㧿㧱㧸㧱㧯㨀ޓ
ޓψ㧲㨕㨚㨕㨟㨔ޓ㧿㨕㨦㨑㧔㧼㧸㧭㧘㨎㨑㨢㨑㨘㧕㧦ޓ㧜㧚㧜㧜㨙㨙
ޓޓ㧲㨕㨚㨕㨟㨔ޓ㧿㨕㨦㨑㧔㧼㧸㧭㧘ޓ㨒㨘㨍㨠㧕㧦ޓ㧜㧚㧜㧜㨙㨙
㧲㨕㨚㨕㨟㨔ޓ㧿㨕㨦㨑㧔㧼㧯ޓ㧘㨎㨑㨢㨑㨘㧕㧦ޓ㧜㧚㧜㧜㨙㨙
ޓޓ㧲㨕㨚㨕㨟㨔ޓ㧿㨕㨦㨑㧔㧼㧯ޓ㧘ޓ㨒㨘㨍㨠㧕㧦ޓ㧜㧚㧜㧜㨙㨙
ޓޓ㧲㨕㨚㨕㨟㨔ޓ㧿㨕㨦㨑㧔㧳㧸㧿㧘㨎㨑㨢㨑㨘㧕㧦ޓ㧜㧚㧜㧜㨙㨙
ޓޓ㧲㨕㨚㨕㨟㨔ޓ㧿㨕㨦㨑㧔㧳㧸㧿㧘ޓ㨒㨘㨍㨠㧕㧦ޓ㧜㧚㧜㧜㨙㨙
㧚ޓ
㧚ޓ
ޓ㧚
㧚ޓ
㧹㧵㧺ޓޓ㧠㧤
㧲㧼㧰㧦㧢㧞㧜㧜ޓޓޓޓޓޓޓޓ 㧲㧼㧰㧦㧢㧞㧜㧜ޓޓޓޓޓޓޓޓ
㧼㧰 㧼㧰 ޓ㧦㧢㧞㧜㧜ޓޓޓޓޓޓޓޓ 㧦㧢㧞㧜㧜ޓޓޓޓޓޓޓޓ
ޓޓޓ㧦ޓޓ㧜㧜ޓޓޓޓޓޓޓޓ ޓޓޓ㧦ޓޓ㧜㧜ޓޓޓޓޓޓޓޓ
㧿㧵㨆㧦ޓ㧜㧜㧜ޓޓޓޓޓޓޓޓ 㧿㧵㨆㧦ޓ㧜㧜㧜ޓޓޓޓޓޓޓޓ
㧭㧯㨀ޓޓޓޓޓޓޓޓޓޓޓޓޓ 㧭㧯㨀ޓޓޓޓޓޓޓޓޓޓޓޓޓ
㧹㧱㧹 㧹㧱㧹㧦ޓޓޓޓޓޓޓޓޓ 㧦ޓޓޓޓޓޓޓޓޓ
㧴㧼㧸 㧴㧼㧸㧼㧺㨀ޓޓޓ㧼㧻㧸ޓޓ 㧼㧺㨀ޓޓޓ㧼㧻㧸ޓޓ㧾