NEC PD78212 User Manual Download | Manualshive

Page: 75 / 487

background image

46

µ

PD78214 Sub-Series

(3) Register bank selection flags (RBS0, RBS1)

These two flags are used to select one of four register banks (see

Table 3-2

).

The flags hold two-bit information indicating the register bank selected by the SEL RBn instruction.

Table 3-2 Selecting a Register Bank

0

0

1

1

Register bank 0

Register bank 1

Register bank 2

Register bank 3

RBS1

0

1

0

1

RBS0

Specified register bank

(4) Auxiliary carry flag (AC)

If an operation generates a carry from bit 3 or a borrow into bit 3, this flag is set (1). Otherwise, the flag is reset
(0).

The flag is used when a BCD conversion instruction is executed.

(5) Zero flag (Z)

If an operation results in zero, this flag is set (1). Otherwise, the flag is reset (0).

(6) Interrupt request enable flag (IE)

This flag controls the CPU’s acknowledgment of interrupt requests.

If the flag is set to 0, interrupts are inhibited. Only nonmaskable interrupts and unmasked macro services can
be acknowledged. All other interrupts are prohibited.

If the flag is set to 1, interrupts are permitted. The ISP flag, interrupt mask flag corresponding to each interrupt
request, and priority designation flag control the acknowledgment of an interrupt request.

When the EI instruction is executed, the IE flag is set (1). When the DI instruction is executed or when an
interrupt is acknowledged, the flag is reset (0).

3.2.3 Stack Pointer (SP)

This 16-bit register holds the first address of a stack area (LIFO: 00000H to 0FFFFH) (see

Fig. 3-8

). The stack pointer

is used to address a stack area when a subroutine is executed or when an interrupt is handled.

The contents of the SP are decremented before data is written into the stack area and incremented after data is
read from the stack area (see

Figs. 3-9 and 3-10

).

A special instruction can access the SP.

The contents of the SP become undefined when RESET is input. Immediately after a reset is released (before a
subroutine is called or before an interrupt is acknowledged), run an initialization program to initialize the SP.

Example

Initializing the SP

MOVW SP, #0FEE0H; SP

←

0FEE0H (if used from FEDFH)

Fig. 3-8 Configuration of the Stack Pointer

SP15

15

SP14

14

SP13

13

SP12

12

SP11

11

SP10

10

SP9

9

SP8

8

SP7

7

SP6

6

SP5

5

SP4

4

SP3

3

SP2

2

SP1

1

SP0

0

SP

«
...
73
74
75
76
77
...
»

Summary of Contents for PD78212








































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PD78212

eXtremeRAID 1100

Brand: Mylex Pages: 74

Brand: Digitus Pages: 8

Brand: ZALMAN Pages: 9

PISO-725 Series

Brand: ICP DAS USA Pages: 8

LinkStation Mini

Brand: Buffalo Pages: 71

Brand: WABCO Pages: 29

Brand: Advantech Pages: 66

Brand: National Instruments Pages: 121

CG9103-2RS232-1USB

Brand: BiPOM Electronics Pages: 8

Brand: Idis Pages: 28

Brand: Baicells Pages: 38

Brand: Zmotion Pages: 57

BioSense Series

Brand: ZKTeco Pages: 96

Audio Plus 3200

Brand: Zoltrix Pages: 34

Brand: National Instruments Pages: 72

S5U13719P00C100

Brand: Epson Pages: 31

Brand: Epson Pages: 34

S1D15722 Series

Brand: Epson Pages: 77

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands