NEC Express 5800/120Lh User Manual Download Page 88

Page: 88 / 314

4-22 Configuring Your Server

SCSI Disk Utilities

This utility scans the SCSI bus for SCSI devices, reports a description of each device. Run these
utilities before configuring SCSI devices.

To enter the utility, select "SCSI Disk Utilities" on the Options menu.

The SCSI ID scan begins displaying the message as shown below.

Scanning SCSI ID:14: Lun Number

AIC-7901 at Slot 00. 23 03:03:00

When the SCSI ID scan completes, the screen listing SCSI IDs and associated devices appears.

Find out the SCSI ID for the installed optional on this screen. You can also view the device
information by selecting a device and pressing

Enter

The following sub menu appears.

SCSI ID#4 : xxxxxxxxx
Firmware : xxxx xxx
Capacity : xxGB

Format

Verify Disk Media

The following table lists submenu items and descriptions.

Submenu item

Description

Format

Formats the selected device in the raw level.

Verify Disk Media

Verifies all the sectors in the selected device. If one or
more bad sectors are found, reassigns the sectors.

HostRAID

Move the cursor onto "HostRAID" and press

Enter

to choose the HostRAID option.

Submenu item

Parameter

Description

HostRAID

Enabled

[Disabled]

Select "Disabled" if the onboard HostRAID

controller is not used.

[ ]: Factory-set

NOTE:

For detail explanation on the HostRAID feature, see

SCSI

Select

Utility User's Manual and Adaptec Storage Manager

Browser Edition User's Guide. You may view or print the SCSI

Select

Utility User's Manual and Adaptec Storage Manager

- Browser

Edition User's Guide from the NEC EXPRESSBUILDER CD-ROM.

Summary of Contents for Express 5800/120Lh



























































































































































































































































































































Search results

Summary of Contents for Express 5800/120Lh

Reviews:

NEC Express 5800/120Lh, User Manual, Page: 88 / 314

Search results

Summary of Contents for Express 5800/120Lh

Reviews: