manualshive.com logo in svg

NEC Express 5800/120Lh, User Manual, Page: 290 / 314

Share
Download
NEC Express 5800/120Lh User Manual Download Page 290

D-6    Installing Windows Server 2003

 

7. 

If the RAID controller (including embedded HostRAID feature) or SCSI controller is
installed, select the proper SCSI Adapter and press 

Enter

.

–

 

Adaptec HostRAID U320 Driver Ver 1.02 For Windows 2000/XP/2003 (When
HostRAID is installed.)

–

 

MegaRAID SCSI 320-1 RAID Controller (When N8103-80F board is installed.)

–

 

MegaRAID SCSI 320-2 RAID Controller (When N8103-81F is installed.)

–

 

Adaptec I2O RAID Driver Disk for 32bit Windows 2000/XP/2003 (When N8103-86F
is installed.)

Continue performing tasks according to the subsequent messages that appear.

After installation is completed, be sure to execute the tasks described in "Driver Installation and
Advanced Settings" and "Updating the System" of this manual.

Summary of Contents for Express 5800/120Lh



























































































































































































































































































































Reviews:

No comments