manualshive.com logo in svg

NEC Express 5800/120Lh, User Manual, Page: 294 / 314

Share
Download
NEC Express 5800/120Lh User Manual Download Page 294

D-10    Installing Windows Server 2003

Procedure for Modifying the Drive Letter

Be careful that the drive letter of the system or boot volume cannot modify with the following
procedure.

 

1. 

Click Start menu, right-click [My Computer], and specify [Manage] to start

[Computer Management].

 

2. 

Specify the [Disk Management] in the left side of the window.

 

3. 

Right-click the volume you want to modify the drive letter and specify the [Change Drive
Letter and Path...].

 

4. 

Click [Yes].

 

5. 

Choose the [Assign a drive letter] and specify the drive letter you want to assign.

 

6. 

Click [OK].

 

7. 

If the following message appears, click [Yes].

Changing the drive letter of a volume may cause programs to no
longer run. Are you sure you want to change this drive letter?

 

8. 

  Close the [Computer Management].

Summary of Contents for Express 5800/120Lh



























































































































































































































































































































Reviews:

No comments