manualshive.com logo in svg

NEC Express 5800/120Lh, User Manual, Page: 162 / 314

Share
Download
NEC Express 5800/120Lh User Manual Download Page 162

6-24    Installing and Using Utilities

BMC ONLINE UPDATE

The optional remote management card includes the Baseboard Management Controller (BMC)
firmware.

The BMC firmware is updated with the BMC Firmware file.

NOTE:

 When the remote management card is installed in the system,

you can use.

IMPORTANT:

 Do not turn DC off during BMC Firmware is updated.

The BMC firmware which is renewed becomes effective after
restarting the system.

Update procedure

 

1. 

Insert NEC EXPRESSBUILDER CD-ROM into the CD-ROM drive.

Master Control Menu of NEC EXPRESSBUILDER will be automatically displayed.

 

2. 

Select [BMC Online Update].

BMC Online Update installer will be started. Follow the installer directions to install.

Summary of Contents for Express 5800/120Lh



























































































































































































































































































































Reviews:

No comments