manualshive.com logo in svg

NEC Express 5800/120Lh, User Manual, Page: 193 / 314

Share
Download
NEC Express 5800/120Lh User Manual Download Page 193

Troubleshooting  8-19

Fail to access the (internal or external) SCSI devices:

T

Is the SCSI device applicable to the server?

→

Operation of any SCSI device that is not authorized by NEC is not guaranteed.

T

Is the cable connection changed?

→

The SCSI connector on the motherboard in the server can be used for either built-
in file devices or external SCSI devices.    The connection to built-in or external
devices can be switched by modifying cable connection properly.    See Chapter
10.

T

Are SCSI devices properly configured?

→

When the server has external SCSI devices connected, hard disk settings,
including SCSI ID and terminator, are required.    Refer to the manual that comes
with the SCSI device for details.

T

Are the SCSI controllers (including optional controllers) properly configured?

→

 

Use the BIOS SETUP utility for proper configuration of SCSI devices connected
to the SCSI connector on the mother board.    When the server has an optional
SCSI controller installed and SCSI devices connected to it, use the BIOS SETUP
utility that comes with the optional SCSI controller for proper configuration.
See the manual that comes with the optional SCSI controller for details.

Summary of Contents for Express 5800/120Lh



























































































































































































































































































































Reviews:

No comments