manualshive.com logo in svg

NEC Express 5800/120Lh, User Manual, Page: 21 / 314

Share
Download
NEC Express 5800/120Lh User Manual Download Page 21

Notes on Using Your Server    1-7

During Operation

CAUTION

Stay away from the fan.

Keep your hand or hair away from the cooling fan on the rear of the server.
Failure to follow this warning may get your hand or hair caught in the fan,
resulting in injury.

Avoid contact with the server during thunderstorms.

Disconnect the power plug from the outlet when a thunderstorm is approaching.
If it starts thundering before you disconnect the power plug, do not touch any
part of the server including the cables.    Failure to follow this warning may cause
a fire or an electric shock.

Keep animals away from the server.

Failure to follow this warning may cause a fire or an electric shock.

Do not place any object on top of the server.

The server may fall and cause property damage to the surroundings.

Do not use a cellular phone or pager around the server.

Turn off the cellular phone or pager.    Radio interference may cause
malfunctions of the server.

Summary of Contents for Express 5800/120Lh



























































































































































































































































































































Reviews:

No comments