manualshive.com logo in svg

NEC Express 5800/120Lh, User Manual, Page: 307 / 314

Share
Download
NEC Express 5800/120Lh User Manual Download Page 307

Installing Windows 2000    E-9

DRIVER INSTALLATION AND ADVANCED SETTINGS

This section describes on how to install and setup various standard drivers mounted on the device.

For the information on installing and setting up the driver that is not described in this section, please
refer to the document attached to the driver.

PROSet

PROSet is a utility that confirms the function of network contained in network driver. Be sure to
install. Utilizing PROSet enables the following issues:

„

 

Confirm detailed information of the adapter.

„

 

Diagnose loop back test, packet transmission test and so on.

„

 

Specify teaming.

Configuring several network adapters as one team provides the server an environment tolerant on
any trouble and enhance through put between the switches.

PROSet is necessary to utilize these features.

Follow the procedure below to install PROSet.

 

1. 

Insert the NEC EXPRESSBUILDER CD-ROM into the CD-ROM drive.

 

2. 

Click Start menu, point to [Program], [Accessory] and click [Explorer].

 

3. 

Run "PROSET.EXE" in the following directory.

<CD-ROM DriveLetter>:\WINNT\W2K\BC3\PROSET\WIN2K\

The [Intel(R) PROSet - InstallShield Wizard] dialog starts.

 

4. 

Click [Next].

 

5. 

Choose "I accept the terms in the license agreement" and click [Next].

 

6. 

Choose "Typical" and click [Next].

 

7. 

Click [Install].

 

8. 

When [InstallShield Wizard Completed] window is displayed, click [Finish].

 

9. 

Restart the system.

Summary of Contents for Express 5800/120Lh



























































































































































































































































































































Reviews:

No comments