NEC Express 5800/120Lh User Manual Download Page 309

Page: 309 / 314

Installing Windows 2000 E-11

Re-install the Network Driver

After installing OS and deleting the network drivers, if you want to re-install the network drivers,
follow the procedure below.

Restart OS and logon to your system.

[Upgrade Device Driver Wizard] dialog box appears.

Click [Next].

Confirm that the [Search for a suitable driver for my device (recommended)] radio button
is selected and click [Next].

Select the [Specify a location] check box and deselect other check boxes.

Click [Next].

Other [Upgrade Device Driver Wizard] dialog box opens.

When using [Intel(R) PRO/1000CT Network Connection],specify [<CD-ROM drive
letter>:\WINNT\W2K\BC3\PRO1000\WIN2K].

Then click [OK].

Click [Next].

Click [Finished].

After re-installing the network drivers, the link speed and Duplex mode need to be
specified.

Refer to "Network Driver" described earlier.

Summary of Contents for Express 5800/120Lh



























































































































































































































































































































Search results

Summary of Contents for Express 5800/120Lh

Reviews:

NEC Express 5800/120Lh, User Manual, Page: 309 / 314

Search results

Summary of Contents for Express 5800/120Lh

Reviews: