manualshive.com logo in svg

NEC Express 5800/120Lh, User Manual, Page: 124 / 314

Share
Download
NEC Express 5800/120Lh User Manual Download Page 124

5-32    Installing the Operating System with Express Setup

Installing and Setting Device Drivers

Follow these steps to install and configure the device drivers.

PROSet

PROSet is a utility that confirms the function of network contained in network driver. Be sure to
install. Utilizing PROSet enables the following issues:

„

 

Confirm detailed information of the adapter.

„

 

Diagnose loop back test, packet transmission test and so on.

„

 

Specify teaming.

Configuring several network adapters as one team provides the server an environment tolerant on
any trouble and enhance throughput between the switches.

PROSet is necessary to utilize these features.

Follow the procedure below to install PROSet.

 

1. 

Insert the NEC EXPRESSBUILDER CD-ROM into the CD-ROM drive.

 

2. 

Click Start menu, point to [Program], [Accessory] and click [Explorer].

 

3. 

Run "PROSET.EXE" in the following directory.

<CD-ROM Drive Letter>:\WINNT\W2K\BC3\PROSET\WIN2K

The [Intel(R) PROSet - InstallShield Wizard] dialog starts.

 

4. 

Click [Next].

 

5. 

Choose "I accept the terms in the license agreement" and click [Next].

 

6. 

Choose "Typical" and click [Next].

 

7. 

Click [Install].

 

8. 

When [InstallShield Wizard Completed] window is displayed, click [Finish].

 

9. 

Restart the system.

Summary of Contents for Express 5800/120Lh



























































































































































































































































































































Reviews:

No comments