NEC Express 5800/120Lh User Manual Download Page 142

Page: 142 / 314

6-4 Installing and Using Utilities

NEC EXPRESSBUILDER for DOS-Based with Local Console

This subsection describes the procedures for using NEC EXPRESSBUILDER for DOS-based with
local console.

Starting NEC EXPRESSBUILDER

The following procedure instructs you to start NEC EXPRESSBUILDER.

IMPORTANT:

Do not remove the NEC EXPRESSBUILDER CD-

ROM while NEC EXPRESSBUILDER is running.

Turn on peripheral devices and the server in this order.

Insert the NEC EXPRESSBUILDER CD-ROM supplied with your server into the CD-
ROM drive of your server.

Ensure that the floppy disk drive is empty.

Press the RESET switch or press

Ctrl

Alt

, and

Delete

to reboot from the NEC

EXPRESSBUILDER. (You may also turn off and then on again to reboot the server.)

NEC EXPRESSBUILDER boots up displaying the top menu.

Summary of Contents for Express 5800/120Lh



























































































































































































































































































































Search results

Summary of Contents for Express 5800/120Lh

Reviews:

NEC Express 5800/120Lh, User Manual, Page: 142 / 314

Search results

Summary of Contents for Express 5800/120Lh

Reviews: