manualshive.com logo in svg

NDD easyone pro, Operator'S Manual, Page: 89 / 188

Share
Download
NDD easyone pro Operator'S Manual Download Page 89

 

EasyOne Pro™ / EasyOne Pro™ LAB

89

Quality Messages and Quality Grades

Low Inspiratory Vol-
ume

Maneuver not 
acceptable. Inspira-
tory volume too low 

The inspiratory volume is smaller 
than 85% FVC/VC/Predicted

Make sure to perform a full expira-
tion before the valve closes, and 
then a full inhalation of test gas

Inspiratory Time Too 
Long

Maneuver not 
acceptable. Inspira-
tion time exceeds 
the maximum of 4 
seconds

Inspiratory time > 4 seconds

Inhale test gas faster

Sampling volume at 
this position too 
large

Sample volume not correctly 
determined

Reduce sample volume

Difference Prepara-
tion and Maneuver

Test cannot be evalu-
ated; gas sensor sig-
nals do not pass QC 
check, possibly due 
to leaks

Reference gas measurement and 
inspiratory gas measurements do 
not match within 80 ppm. This 
means that most probably there is 
a leak in the DLCO hose

Check for leaks; check gas supply

Sampling volume at 
maximum position 

Test cannot be evalu-
ated; exhaled vol-
ume too small

Can happen when very small vol-
umes are exhaled

Collection bar is beyond rightmost 
position

Activate „Automatically rejected 
volume“

After the breath hold, do not 
exhale too fast.

DLCO-Warning: High 
inspiratory CO dur-
ing tidal breathing!

An increased CO level was 
detected during the tidal breath-
ing phase.

Check the DLCO valve unit.

If the error occurs repeatedly then 
please contact service.

Test error: # of 
breaths

Test cannot be evalu-
ated; DLCO maneu-
ver cannot be 
detected

Number of breaths during DLCO 
expiration could not be detected

Perform the DLCO maneuver with 
full effort

Message

Criterion

Recommended action

Summary of Contents for easyone pro





























































































































































































Reviews:

No comments