manualshive.com logo in svg

NDD easyone pro, Operator'S Manual, Page: 48 / 188

Share
Download
NDD easyone pro Operator'S Manual Download Page 48

Performing a Test

48

EasyOne Pro™ / EasyOne Pro™ LAB

 

controls, such as ventilation, air filtration or ultraviolet 
decontamination of air, should be used to prevent disease 
transmission.

Risk of Infection—Clean the nose clip after each patient.

Measurement

Insert the new 

spirette™

 in the sensor.

Attach the nose clip to the patient.

Press 

Start

.

The device advises you to keep the 

spirette™

 closed until the test start 

prompt is displayed. This is necessary to set the baseline correctly. 

Note

ndd recommends leaving the spirette™ packaging in place 
until after the baseline has been set.

Block off the 

spirette™

 on one end and confirm the message with 

OK

.

When the start test prompt is displayed, hand the sensor over to your 
patient and instruct him or her to perform the maneuver as explained 
earlier.

Note

 If the "Manual Test Stop" option was selected in the 
configuration (see 

"Test Tab" 

on page 116), the operator 

must terminate the measurement by clicking the Test End 
button or by pressing the space bar or the Enter key.

During the test, you will see the flow-volume loop and the volume-time 
curve on the display. All curves and measured values will be displayed after 
the test.

Summary of Contents for easyone pro





























































































































































































Reviews:

No comments