manualshive.com logo in svg

NDD easyone pro, Operator'S Manual, Page: 37 / 188

Share
Download
NDD easyone pro Operator'S Manual Download Page 37

 

EasyOne Pro™ / EasyOne Pro™ LAB

37

Start-up and Initial Preparation

spirette™

Note

The device is to be operated only with the original ndd 

spirette™

.

Warning

Cross Contamination Between Patients—The 

spirette™

 is 

intended for single patient use. Use a new one for each 
patient  to prevent cross contamination between patients.

Tear open the plastic bag containing the 

spirette™

 and fold the bag back 

so that you can insert the 

spirette™

 in the flow sensor.

 

Ensure that the 

plastic bag protects the mouthpiece of the 

 spirette™

 

 

until you hand the 

flow sensor

 

over to the patient.

 

This approach not only ensures perfectly hygienic conditions, it also keeps 
the 

spirette™

 closed for subsequent setting of the baseline.

Insert the 

spirette™

 - as shown in the illustration - into the flow sensor 

as far as possible. When doing this, please ensure that the arrow on the 

spirette™

 is lined up with the arrow on the flow sensor. 

You remove the 

spirette™

 by pushing it out of the sensor from below.

Fig. 2-21

Inserting the FRC barriette™

Summary of Contents for easyone pro





























































































































































































Reviews:

No comments