manualshive.com logo in svg

NDD easyone pro, Operator'S Manual, Page: 163 / 188

Share
Download
NDD easyone pro Operator'S Manual Download Page 163

 

EasyOne Pro™ / EasyOne Pro™ LAB

163

Appendix

regarding the device or the software do not originate from, and are 
not binding on, Microsoft or its affiliates. When allowed by your 
local laws, 

ndd Medizintechnik AG

 and Microsoft exclude implied 

warranties of merchantability, fitness for a particular purpose and 
non-infringement. 

12.

Liability Limitations.  You can recover from Microsoft and its 
affiliates only direct damages up to two hundred fifty U.S. Dollars 
(U.S. $250.00). You cannot recover any other damages, including 
consequential, lost profits, special, indirect or incidental damages.

This limitation applies to:

Anything related to the software, services, content (including 
code) on third party internet sites, or third party programs; and

Claims for breach of contract, breach of warranty, guarantee or 
condition, strict liability, negligence, or other tort to the extent 
permitted by applicable law.

It also applies even if Microsoft should have been aware of the possi-
bility of the damages. The above limitation may not apply to you 
because your country may not allow the exclusion or limitation of 
incidental, consequential or other damages.

13.

Export Restrictions.

 The software is subject to United States export 

laws and regulations. You must comply with all domestic and 
international export laws and regulations that apply to the software. 
These laws include restrictions on destinations, end users and end 
use. For additional information, see www.microsoft.com/exporting. 

Summary of Contents for easyone pro





























































































































































































Reviews:

No comments