manualshive.com logo in svg

NDD easyone pro, Operator'S Manual, Page: 159 / 188

Share
Download
NDD easyone pro Operator'S Manual Download Page 159

 

EasyOne Pro™ / EasyOne Pro™ LAB

159

Appendix

As described below, using some features also operates as your consent 
to the transmission of certain standard computer information for Inter-
net-based services.

By using the software, you accept these terms. If you do not accept 
them, do not use or copy the software. Instead, contact 

ndd Mediz-

intechnik AG

 to determine its return policy for a refund or credit.

If you comply with these license terms, you have the rights below.

1. Use Rights.

You may use the software on the device with which you acquired the soft-
ware.

2. Additional Licensing Requirements and/or Use Rights. 

Specific Use

. ndd Medizintechnik AG designed this device for a 

specific use. You may only use the software for that use.

Other Software

. You may use other programs with the software as 

long as the other programs

Directly support the manufacturer's specific use for the device, or

Provide system utilities, resource management, or anti-virus or 

similar protection. 

Software that provides consumer or business tasks or processes may 
not be run on the device. This includes email, word processing, 
spreadsheet, database, scheduling and personal finance software. 
The device may use terminal services protocols to access such soft-
ware running on a server.

Device Connections.

You may use terminal services protocols to connect the device to 

another device running business task or processes software such 
as email, word processing, scheduling or spreadsheets.

You may allow up to ten other devices to access the software to 

use 

File Services, 

Print Services, 

Internet Information Services, and 

Internet Connection Sharing and Telephony Services.

The ten connection limit applies to devices that access the software 
indirectly through "multiplexing" or other software or hardware that 
pools connections. You may use unlimited inbound connections at 
any time via TCP/IP.

3. Scope of License

. The software is licensed, not sold. This agreement 

only gives you some rights to use the software. 

ndd Medizintechnik AG

 

and Microsoft reserve all other rights. Unless applicable law gives you 
more rights despite this limitation, you may use the software only as 
expressly permitted in this agreement. In doing so, you must comply 
with any technical limitations in the software that allow you to use it 

Summary of Contents for easyone pro





























































































































































































Reviews:

No comments