manualshive.com logo in svg

NDD easyone pro, Operator'S Manual, Page: 160 / 188

Share
Download
NDD easyone pro Operator'S Manual Download Page 160

Appendix

160

EasyOne Pro™ / EasyOne Pro™ LAB

 

only in certain ways. For more information, see the software 
documentation or contact 

ndd Medizintechnik AG

. Except and only to 

the extent permitted by applicable law despite these limitations, you 
may not:

Work around any technical limitations in the software;

Reverse engineer, decompile or disassemble the software;

Make more copies of the software than specified in this agreement;

Publish the software for others to copy;

Rent, lease or lend the software; or

Use the software for commercial software hosting services.

Except as expressly provided in this agreement, rights to access the soft-
ware on this device do not give you any right to implement Microsoft pat-
ents or other Microsoft intellectual property in software or devices that 
access this device.

You may use remote access technologies in the software such as Remote 
Desktop to access the software remotely from another device. You are 
responsible for obtaining any licenses required for use of these protocols 
to access other software.

Remote Boot Feature. If the 

ndd Medizintechnik AG

 enabled the 

device Remote Boot feature of the software, you may

use the Remote Boot Installation Service (RBIS) tool only to 

install one copy of the software on your server and to deploy the 
software on licensed devices as part of the Remote Boot process; 
and

use the Remote Boot Installation Service only for deployment of 

the software to devices as part of the Remote Boot process; and

download the software to licensed devices and use it on them.

For more information, please refer to the device documentation or 
contact 

ndd Medizintechnik AG

.

Internet-Based Services

. Microsoft provides Internet-based services 

with the software. Microsoft may change or cancel them at any time.

Consent for Internet-Based Services

. The software features 

described below connect to Microsoft or service provider 
computer systems over the Internet. In some cases, you will not 
receive a separate notice when they connect. You may switch off 
these features or not use them. For more information about these 
features, visit

http://www.microsoft.com/windowsxp/downloads/updates/
sp2/docs/privacy.mspx.

By using these features, you consent to the transmission of this 
information. Microsoft does not use the information to identify or 
contact you.

Summary of Contents for easyone pro





























































































































































































Reviews:

No comments