manualshive.com logo in svg

NDD easyone pro, Operator'S Manual, Page: 12 / 188

Share
Download
NDD easyone pro Operator'S Manual Download Page 12

Introduction

12

EasyOne Pro™ / EasyOne Pro™ LAB

 

The patient should never be left unattended during the 
tests.

The following should be available throughout provocation 
tests:
- a medical specialist capable of treating acute 
bronchospams
- appropriate medication as well as resuscitation 
equipment (defibrillator, cardiac pacemaker) 

Refer to the relevant literature for creating safe protocols 
for bronchial provocation tests. Examples are: Sterk PJ, 
Fabbri LM, Quanjer PhH, et al. Airway responsiveness. 
Standardized challenge testing with pharmacological, 
physical and sensitizing stimuli in adults. Report Working 
Party Standardization of Lung Function Tests. European 
Community for Steel and Coal. Official position of the 
European Respiratory Society. Eur Respir J 1993; 6: 
Suppl.16, 53–83).

Caution

Equipment Damage—Before connecting the device to the 
power line, check that the voltage and frequency ratings of 
your power line match the values indicated on the device 
nameplate.

Equipment Damage—Protect the equipment from viruses, 
malware, etc. Always check the USB flash drive for viruses, 
before connecting it to the equipment.

Equipment Damage—Do not set up 

EasyOne Pro™

 in the 

direct vicinity of a window. Rain, humidity and sunlight may 
damage 

EasyOne Pro™

. Do not operate 

EasyOne Pro™

 in 

the vicinity of heating appliances (radiators). Do not block air 
vents and do not place any objects on the device.

Equipment Damage—Do not drop 

EasyOne Pro™

.

Equipment Damage—For equipment transport, switch off 

EasyOne Pro™

 and store it in its original packing.

Restricted Sale—U.S. Federal law restricts this device to sale 
by or on the order of a physician.

Summary of Contents for easyone pro





























































































































































































Reviews:

No comments