manualshive.com logo in svg

NDD easyone pro, Operator'S Manual, Page: 50 / 188

Share
Download
NDD easyone pro Operator'S Manual Download Page 50

Performing a Test

50

EasyOne Pro™ / EasyOne Pro™ LAB

 

When three acceptable tests have been performed, the message 

Session 

complete!

 appears and a quality grade from 

A

 (optimal) to 

F

 

a

 is displayed.

Note

If FEV6 is selected (instead of FVC), the measurement will 
stop automatically after 6 seconds.

%Pred Graph

The %Pred graph is a three-segment bar. The left segment 

a

 indicates a 

value below the lower limit of normal, the middle segment 

b

 represents a 

value between the lower limit and the predicted value and the right seg-
ment 

c

 indicates a value above the predicted value. FVC, FEV1 and FEV1/

FVC are displayed in color, all other parameters are grey.

Fig. 3-11 Acquisition screen after three acceptable, expiratory FVC tests

a

c

b

a Quality grade
b Click to perform a post-trial (see 

"Bron-

chodilation (Post-Tests)" 

on page 53)

c Area for review comments

Fig. 3-12 %Pred graph

a

b

c

Summary of Contents for easyone pro





























































































































































































Reviews:

No comments