NDD easyone pro Operator'S Manual Download Page 28

Page: 28 / 188

Start-up and Initial Preparation

EasyOne Pro™ / EasyOne Pro™ LAB

If the tube end shows signs of mechanical damage
(grooves), cut off the damaged portion.



Connect the other end of the tube to the pressure relief valve



Open the main valve

of the gas cylinder completely.



Slowly open the pressure relief valve

and set the manometer

to a

secondary pressure of 4 to 5 bar.

Note

A DLCO overpressure valve that opens at 7.5 bar is integrated
in the device. If you select a higher secondary pressure, the
overpressure valve will open and gas will escape.

Exchange the gas cylinder if the primary pressure drops
below 10 bar!

Warning

Be sure not to confuse the DLCO gas inlet and the FRC gas
inlet.

Fig. 2-11

Connection for tube from DLCO gas cylinder

Summary of Contents for easyone pro





























































































































































































Search results

Summary of Contents for easyone pro

Reviews:

NDD easyone pro, Operator'S Manual, Page: 28 / 188

Search results

Summary of Contents for easyone pro

Reviews: