manualshive.com logo in svg

NDD easyone pro, Operator'S Manual, Page: 158 / 188

Share
Download
NDD easyone pro Operator'S Manual Download Page 158

Appendix

158

EasyOne Pro™ / EasyOne Pro™ LAB

 

Compliant Cables and Accessories

Warning

The use of accessories, transducers and cables other than 
those specified may result in increased emissions or 
decreased immunity performance of the equipment or 
system

The table below lists cables, transducers, and other applicable accessories 
with which ndd claims EMC compliance.  

Note

Any supplied accessories that do not affect EMC compliance are            
not included.

12.8 Microsoft Software License Terms for Windows

®

 XP 

Embedded Runtime

These license terms are an agreement between you and 

ndd Medizintech-

nik AG

. Please read them. They apply to the software included on this 

device. The software also includes any separate media on which you 
received the software.

The software on this device includes software licensed from Microsoft Cor-
poration or its affiliate.

The terms also apply to any Microsoft

Updates, 

Supplements, 

Internet-based services, and

Support services

for this software, unless other terms accompany those items. If so, those 
terms apply. If you obtain updates or supplements directly from Microsoft, 
then Microsoft, and not 

ndd Medizintechnik AG

, licenses those to you.

Ethernet cable, 1.5 m, shielded

USB cable, 2 m, shielded

VGA cable including 2 ferrites, 1.8 m, shielded

Sensor cable, 1.7 m, shielded

Temperature / humidity sensor cable, 0.4 m, shielded

Summary of Contents for easyone pro





























































































































































































Reviews:

No comments