manualshive.com logo in svg

NDD easyone pro, Operator'S Manual, Page: 8 / 188

Share
Download
NDD easyone pro Operator'S Manual Download Page 8

Introduction

8

EasyOne Pro™ / EasyOne Pro™ LAB

 

Definitions

In this manual the safety information is classified as follows:

Danger

indicates an imminent hazard. If not avoided, the hazard will 
result in death or serious injury.

Warning

indicates a hazard. If not avoided, the hazard can result in 
death or serious injury.

Caution

indicates a potential hazard. If not avoided, the hazard may 
result in minor injury and/or product/property damage.

Safety Notices

Danger

Explosion Hazard—

EasyOne Pro™

 is not designed for use in 

areas of medical locations where an explosion hazard may 
exist. Explosion hazards may result from the use of 
flammable anesthetics, skin cleansing agents or 
disinfectants. Great care must be exercised when the system 
is used in an oxygen-enriched atmosphere. The atmosphere 
is considered to be oxygen-enriched when the room air 
contains more than 25% of oxygen or nitrous oxide.

Summary of Contents for easyone pro





























































































































































































Reviews:

No comments