manualshive.com logo in svg

NDD easyone pro, Operator'S Manual, Page: 52 / 188

Share
Download
NDD easyone pro Operator'S Manual Download Page 52

Performing a Test

52

EasyOne Pro™ / EasyOne Pro™ LAB

 

 

Edit the values, if necessary, and click 

Confirm >>

 to close the window.

Warning

Erroneous Measurement Results—Incorrect entries may lead 
to erroneous test readings and incorrect system 
interpretations. The specified measuring accuracy is ensured 
only when all entries are correct.

The inspiratory and expiratory FVL test acquisition screen appears.

Measurement

Prepare the patient (see 

"Preparations" 

on page 46) and explain the test 

maneuvers to him or her:

take the 

spirette™

 into the mouth with the lips sealing around the 

spirette™

, taking care not to block its opening with the tongue or bite 

down excessively on the 

spirette™

 

breathe calmly

fill lungs completely

exhale as hard and fast as possible

continue blowing out until the lungs are completely empty

inhale as hard and fast as possible.

Fig. 3-14

Window showing the ambient conditions

a b c

d

e

f

a Conversion factors
b Box for entry of the humidity
c Box for entry of the ambient temperature
d Box for entry of the altitude (atmospheric 

pressure)

e Click to recalculate the BTPS factor (if the 

ambient conditions were modified) 

f Click to confirm and accept the values

Summary of Contents for easyone pro





























































































































































































Reviews:

No comments