NDD easyone pro Operator'S Manual Download Page 36

Page: 36 / 188

Start-up and Initial Preparation

EasyOne Pro™ / EasyOne Pro™ LAB



Insert the

DLCO barriette™

in the one-way valve (aligning the arrows) as

shown in Fig. 2-20 and check that it sits tight.

FRC barriette™

(

EasyOne Pro™ LAB

only)

Note

The

FRC barriette™

is required only when also FRC tests will

be performed with the

EasyOne Pro™ LAB

. If the

EasyOne

Pro™ LAB

is used for DLCO testing, the

DLCO barriette™

will

also have to be attached here.
The device is to be operated only with the original ndd

FRC

barriette™.

Warning

Cross Contamination Between Patients—The

FRC barriette™

is intended for single patient use. Use a new one for each
patient to prevent cross contamination between patients.

Fig. 2-20

Inserting the DLCO barriette™

Summary of Contents for easyone pro





























































































































































































Search results

Summary of Contents for easyone pro

Reviews:

NDD easyone pro, Operator'S Manual, Page: 36 / 188

Search results

Summary of Contents for easyone pro

Reviews: