manualshive.com logo in svg

NDD easyone pro, Operator'S Manual, Page: 71 / 188

Share
Download
NDD easyone pro Operator'S Manual Download Page 71

 

EasyOne Pro™ / EasyOne Pro™ LAB

71

Performing a Test

3.9 FRC Test (

EasyOne Pro™ LAB

 only)

Introduction

FRC measurement is based on the nitrogen (N

2

) washout method where N

2

 

is washed out from the lungs while the patient breathes 100% oxygen. The 
test is performed during tidal breathing within the range indicated at 

a

 (Fig. 

3-26). After a (configurable) number of breaths, the measurement starts 
automatically or it can be started manually with the 

Activate

 button.

Note

Before conducting the FRC test, the valve unit must be 
attached to the flow sensor (see Fig. 2-7). Furthermore, a new 

FRC barriette™

 and, if a new patient is tested, a new 

spirette™

 must be inserted (see 

"Inserting the One-Way 

Valve, DLCO barriette™/FRC barriette™ and spirette™" 

on 

page 35).

Before performing the first FRC test, check that the valve unit is 
properly attached and that the metal coupling ring of the 
motor is tight.

Inform patients that they may experience a feeling of dryness 
during inhalation. Also, they will hear oxygen escape during 
the washout phase.

You can choose between the following tests:

manual mode

automatic mode.

Additionally, the FRC test linked with SVC is available (

Linked FRC Test with 

SVC (online)

), see 

"FRC (mbw) Tab" 

on page 122):

No linked SVC

SVC before washout

SVC after washout.

Note

The method recommended by ATS/ERS is the linked SVC test.

No linked SVC

Only a plain FRC washout is performed. If an SVC test has been 
performed before, the lung volume parameters, such as TLC, 
ERV and RV, will be calculated based on this external SVC test.

Summary of Contents for easyone pro





























































































































































































Reviews:

No comments