Muller TOUCH800 Installation And Operating Instructions Manual Download Page 84

Page: 84 / 85

Troubleshooting

V9.20191001

30322538-02-EN

Troubleshooting

The following error messages can appear during operation, amongst others:

General

Error message text

Possible cause

Possible error correction

Some files could not be deleted.

The files that should be deleted are
currently being used.

Object pool error

Delete the object pool and restart the

terminal. [

➙

49]

ECU: Offline - The connection has been
broken.

The connections between the terminal and
ECU have been broken.

Check the connection. [

➙

17]

GPS

Error message text

Possible cause

Possible error correction

GPS receiver reset failed.

The wrong driver was selected.

Select the correct driver. [

➙

28]

The external lightbar is activated.

Deactivate the external lightbar [

➙

40]

and connect the GPS receiver directly to

the terminal. [

➙

28]

The GPS receiver is not enabled for E-Dif. There is no E-Dif activation on the GPS

receiver.

Please contact technical support.

GPS receiver has been removed.

The connection between the terminal and
GPS receiver has been broken.

Check the connection. [

➙

28]

The GPS receiver has been configured for
TRACK-Leader AUTO.

Reset the baud rate for the GPS receiver.

[

➙

30]

GPS receiver not initialized.

The terminal does not recognise the
configuration of the GPS receiver.

Reset the GPS receiver to its factory

settings. [

➙

30]

Timeout.

The wrong driver was selected.

Select the correct driver. [

➙

28]

The external lightbar is activated.

Deactivate the external lightbar [

➙

40]

and connect the GPS receiver directly to

the terminal. [

➙

28]

SIM card is not unlocked.

The PIN request for the SIM card is
activated.

Deactivate the PIN request for the SIM
card.

Invalid entry.

Unauthorised special characters were
used in the entry.

Correct the entry.

The connected receiver could not be
recognized.

The wrong driver was selected.

Select the correct driver. [

➙

28]

An unknown GPS receiver has been
connected.

Use the default GPS driver. [

➙

28]

Summary of Contents for TOUCH800






















































































Search results

Summary of Contents for TOUCH800

Reviews:

Related manuals for TOUCH800

Brands by name

Popular brands

Muller TOUCH800, Installation And Operating Instructions Manual

Search results

Summary of Contents for TOUCH800

Reviews:

Related manuals for TOUCH800

Brands by name

Popular brands