manualshive.com logo in svg

MTU 20V4000G*3 series, Operating Instructions Manual

Share
Download
MTU 20V4000G*3 series Operating Instructions Manual Download Page 291

9.21.2 Engine governor plug connections – Check

Preconditions

☑

Engine stopped and starting disabled.

☑

Electronic engine management system is de-energized.

NOTICE

Insertion of unsuitable test probe, e.g. test prod.
The contacts in the plug connection can be bent!
• Carry out check of plug connection only with test connectors.

Checking plug connections at engine governor

1.

Check all plug connections for secure seating.

2.

Lock loose connectors.

3.

Check dust cap on ECU and EXU connectors for damage and correct seating.

MS150093/05E 2018-12

| Accessories for (Electronic) Engine Governor / Control System  | 289

TIM-ID: 0000000048 - 009

Summary of Contents for 20V4000G*3 series






















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands