manualshive.com logo in svg

MTU 20V4000G*3 series, Operating Instructions Manual

Share
Download
MTU 20V4000G*3 series Operating Instructions Manual Download Page 10

Replacing components with emission labels

On all MTU engines fitted with emission labels, these labels must remain on the engine throughout its opera-
tional life.

Exception: Engines used exclusively in land-based, military applications other than by US government agen-
cies.

Please note the following when replacing components with emission labels:
• The relevant emission labels must be affixed to the spare part.
• Emission labels shall not be transferred from the replaced part to the spare part.
• The emission labels must be removed from the replaced part and destroyed.

8 | Safety  | MS150093/05E 2018-12

TIM-ID: 0000040530 - 014

Summary of Contents for 20V4000G*3 series






















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands