manualshive.com logo in svg

MTU 20V4000G*3 series, Operating Instructions Manual

Share
Download
MTU 20V4000G*3 series Operating Instructions Manual Download Page 139

Blue exhaust gas

Cause

Corrective action

Too much engine oil in the engine

u

Drain engine oil (→ Page 240).

Oil separator of crankcase
breather contaminated

u

Replace filter (→ Page 197).

Exhaust turbocharger, cylinder
head, piston rings or cylinder liner
defective

u

Contact Service.

White exhaust gas

Cause

Corrective action

Engine is not at operating
temperature

u

Run engine to reach operating temperature.

Water in fuel

u

Check fuel system on fuel prefilter;
Drain water from fuel prefilter (not switchable) (→ Page 221).
Drain fuel prefilter (switchable) (→ Page 223).

Intercooler leaky

u

Contact Service.

MS150093/05E 2018-12

| Troubleshooting | 137

TIM-ID: 0000074300 - 001

Summary of Contents for 20V4000G*3 series






















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands