manualshive.com logo in svg

MTU 20V4000G*3 series, Operating Instructions Manual

Share
Download
MTU 20V4000G*3 series Operating Instructions Manual Download Page 284

9.16.5 Charge-air coolant pump – Relief bore check

DANGER

Components are moving or rotating.
Risk of crushing, danger of parts of the body being caught or pulled in!
• Operate the engine at low load only. Keep clear of the danger zone of the engine.

WARNING

A high level of noise is produced when the engine is running.
Risk of hearing loss!
• Wear suitable hearing protection.

Charge-air coolant pump – Re-
lief bore check

1.

Check relief bore for oil and coolant dis-
charge.

2.

Stop engine (→ Page 129) and disable engine
start, observe general safety instructions for
maintenance and repair.

3.

Clean the relief bore with a wire if it is conta-
minated.
• Permissible coolant discharge: up to 10

drops per hour.

• Permissible oil discharge: up to 5 drops

per hour.

4.

If discharge exceeds the specified limits:
Contact Service.

282 | Low-Temperature Circuit | MS150093/05E 2018-12

TIM-ID: 0000000964 - 009

Summary of Contents for 20V4000G*3 series






















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands