manualshive.com logo in svg

MTU 20V4000G*3 series, Operating Instructions Manual

Share
Download
MTU 20V4000G*3 series Operating Instructions Manual Download Page 251

Checking strainer

Item

Findings

Task

Strainer

Metallic residues

• Clean
• Monitor engine operation
• Check strainer daily
• Contact Service.

Strainer

Damaged

Replace

Square section ring

Damaged

Replace

Spring

Damaged

Replace

O-ring

Damaged

Replace

Installing strainer

1.

Coat square section ring on basket strainer (5) with engine oil and install basket strainer (5).

2.

Coat O-ring (3) with engine and install in filter housing.

3.

Move spring (4) into fitting position.

4.

Install cover (2) and secure with screws (1).

MS150093/05E 2018-12

| Oil Filtration / Cooling | 249

TIM-ID: 0000036227 - 010

Summary of Contents for 20V4000G*3 series






















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands