manualshive.com logo in svg

MTU 20V4000G*3 series, Operating Instructions Manual

Share
Download
MTU 20V4000G*3 series Operating Instructions Manual Download Page 199

9.3 Crankcase Breather

9.3.1 Crankcase breather – Oil mist separator replacement

Preconditions

☑

Engine is stopped and starting disabled.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Engine oil
Oil mist separator

(→ Spare Parts Catalog)

O-ring

(→ Spare Parts Catalog)

WARNING

Oil is hot.
Oil can contain residue/substances which are harmful to health.
Risk of injury and poisoning!
• Allow the product to cool to below 50 °C before beginning work.
• Wear protective clothing, protective gloves and goggles/safety mask.
• Avoid contact with skin.
• Do not inhale oil vapor.

Oil mist separator – Replace-
ment

1.

Remove screws (1) and take off together with
retainer (2).

2.

Replace oil mist separator (3).

3.

Replace O-ring (4) if necessary.

4.

Replace further oil mist separators in the
same way.

MS150093/05E 2018-12

| Crankcase Breather | 197

TIM-ID: 0000018590 - 010

Summary of Contents for 20V4000G*3 series






















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands