MSI CellScale 3750CS User Manual Download Page 92

Page: 92 / 94

Page 92 MSI-3750CS RF Weighmeter • User Guide

3750CS

ELL

CALE RF DIGITAL WEIGHT INDICATOR

8th output is a TTL compatible Logic output. Connections are

made through liquid tight feed through connectors to screw less

terminal blocks.

Audible Set Points or Totalize Indicator

Coupled with the internal Set Points, an alarm can sound at any

weight. Can also be used for accept or an out-of-limits indicator

for blind check-weighing. Can also be configured as a totalize

alert.

External Totalize Switch

(included with Audible Totalize Indicator)

A transient protected switch input with connector for remote

totalize switch. Normally open momentary switch is supplied by

the end user. Supplied with 13’ (4m) cable.

Long Range Antenna

A 9dBi gain antenna with a 10’ (3m) low loss coaxial cable.

Increases transmission range and allows for remote locating the

Antenna.

Mounting Bracket

For Wall or Bulkhead Mounting. 180° Swing

Summary of Contents for CellScale 3750CS































































































Search results

Summary of Contents for CellScale 3750CS

Reviews:

Related manuals for CellScale 3750CS

Brands by name

Popular brands

MSI CellScale 3750CS, User Manual

Search results

Summary of Contents for CellScale 3750CS

Reviews:

Related manuals for CellScale 3750CS

Brands by name

Popular brands