MSI CellScale 3750CS User Manual Download Page 91

Page: 91 / 94

MSI-9000 CellScale

System • 3750CS User Guide Page 91

MEASUREMENT SYSTEMS INTERNATIONAL

Software V1-15 to 1-20

APPENDIX C – SPECIFICATIONS &

SUMMARY OF FEATURES

Temperature Range

• -10° C to +40° C NTEP / OIML certified range

• -20° C to +60° C Operating (-4° F to 140° F)

• -40° C to +80° C Storage (-40° F to 176° F)

Approvals (planned or pending)

NTEP, OIML, Factory Mutual, NEMA, FCC

Radio Link

Frequency Hopping Spread Spectrum in 32 channels @ 2.4 GHz.

Allows 32 networks of multiple scales. Radio functions in the

ISM band, license free in the USA and Europe. 10mW (low

power) or 100mW (high power) average output.

Radio Link Effective Range

Typically 500’ (150 meters) indoors, standard antennas

Up to 10 miles (16 kilometers) outdoors with gain antennas

RFI/EMI Shielding

Exceeds NIST HB44 and CE Standards.

Housing

Alodined and powder coated cast aluminum. ‘O’ ring gasketed.

NEMA 4, IP66

Connectors

Power and Comm connections are made with heavy duty water-

proof industrial connectors. (Euro Style). Antenna connector is

standard TNC (models manufactured in 2000 use a reversed pin

SMA). Set Points internally wired with cables sealed through

water-tight feedthroughs (glands).

Weight

6.2 lb. (2.8 kg)

STANDARD FEATURES

Scale Monitoring

Each 3750CS can log on to 5 different networks allowing one

meter to serve for 5 separate CellScales. Easy 1 button scale

changes. Each CellScale can access 32 independent Scale Chan-

nels

Calibration

Via RF, the 3750CS can calibrate any CellScale system. Sealing

the system is not necessary due to password protected audit trail

information. Full “Audit Trail” tracking with calibration date,

parametric information, and authorization information may be

printed out the 3750CS Comm Port.

Keypad

23 keys – 5 user programmable, 10 key alphanumeric, and 8

scale control keys

Push button Functions

Fixed keys:

Power: On/Off

Zero: Remove residual weight on scale

Net/Gross: Switch between Tared weight (Net) and Gross weight

Tare: Tare out empty container weight and switch to Net mode.

Print: Output user configured print strings to Comm Port

Alpha: Allows alpha character entry, upper and lower case

Enter: Store parameters or enter menus

Setup: Setup scale functions

0-9 with Alpha characters

Function Keys: 5 function keys are set able to any of the following

functions:

Total: Add the current weight to the total, or Auto Total On/Off

Grand Total: Display totaled weight of all ID Codes

1KeyClear Total: Clears current IDs Total

2KeyClear Total: Clears current IDs Total, requires confirmation

Clear Last Total: Clears only last weighment

Statistics: Display stats of current ID Code

View

∑

: Displays totaled weight of the current ID.

ID#: Push to change the ID code

Set Points: Set and configure set points

Units: Change weight units

Modem: Configure RF Modem

RF Network: Set Network parameters and switch into up to 5

RF Networks.

SC Index: Switch between selected scale channels

Clear Latch: Used to cleared latched Set Points.

Peak Hold: Captures maximum readings

String1 and String 2: Displays user configured print strings asso-

ciated with each ID.

Test: Performs LCD display test.

Units: 1 button access to switching weight units.

Disabled: no function assigned

Programmable Features

• Automatic or Manual Tare entry

• 32 Set points with messaging capability

• Peak Hold – for capturing maximum readings

• 32 programmable ID Codes

• Each ID code has an 8 character name, two 20 character

print strings, and stores independently units, tare, total with

weighments counter, and full statistics (Std Dev, Min, Max, Avg,

Variance).

• Automatic Power-Down, for power saving in battery applications

• Backlight On, Off or Automatic

• Lock –The user can lock any or all features to prevent tampering

with setups. Protected by password.

• RS-232 Option will output on demand, on a change, regular

time interval, on a set point, on Total, by computer control or

continuously.

• RS-232 I/O provides full output formatting to interface with

computers, printers, scoreboards and most serial devices.

• Host commands to control the 3750CS from any computer.

• Any weight unit can be turned on or off

Display

• 6 digit .9”/23 mm numeric weight LC display

• 8 digit 0.45”/11 mm alphanumeric LCD (message / units dis-

play / Total Weight display)

• 21 Segment Bar graph for process control % indications, RF

Activity.

• Annunciators for measurement modes

• Sunlight visible LED indicator for Totals, Set Pts 1 and 2

• Photocell activated fiber-optic LED backlighting

Calibration Parameters

See CellScale specifications. All calibration data is stored in

the CellScale, allowing any 3750CS to use any CellScale based

system without recalibration.

Real Time Clock

Supports date / time stamping in US or European time and date.

Backed up by a replaceable Lithium Battery (Typical life >5

years).

Data I/O

1 Comm Port, RS-232. Baud Rates: 300, 600,1200, 2400, 4800,

9600, 14.4k, 19.2k, 38.4k. CTS/RTS handshaking. User config-

ured software handshaking.

Up to 32 IDs can be stored in any connected CellScales and are

identified by Alpha-numeric ID names. Each ID stores Totals,

Statistics, Tare values, and two 20 byte string messages.

Totalizing & Statistics

Stored in connected CellScales, printed from the 3750CS. Inter-

nal or external connected Push button or Automatic. Total weight

up to 999,999,999. Weighments counter up to 65,535. Totals

and statistics are stored with each ID register. Each ID code

keeps full statistics on totaled weighments. Included are Standard

Deviation, Average, Minimum, Maximum, and Coefficient of

Variance.

OPTIONS

Vehicle Power Supply

Transient protected Power Supply for operating the 3750CS from

vehicles. Available in two ranges: 9-36Vdc and 18-60Vdc. Sup-

plied with 13’ (4m) cable.

Universal Power Supply

90-260Vac or 130-350Vdc Option. Requires Vehicle Power

Supply option.

Set Point Relays

The Set Point relays provide up to 8 set point outputs for inter-

facing to external devices such as warning lights, process relays,

or sirens. 7 SPDT (form C) 1A/115VAC relays are provided

internal to the 3750CS meter for direct set-point interfacing. The

Summary of Contents for CellScale 3750CS































































































Search results

Summary of Contents for CellScale 3750CS

Reviews:

Related manuals for CellScale 3750CS

Brands by name

Popular brands

MSI CellScale 3750CS, User Manual

Search results

Summary of Contents for CellScale 3750CS

Reviews:

Related manuals for CellScale 3750CS

Brands by name

Popular brands