MSI CellScale 3750CS User Manual Download Page 10

Page: 10 / 94

Page 10 MSI-3750CS RF Weighmeter • User Guide

3750CS

ELL

CALE RF DIGITAL WEIGHT INDICATOR

The 3750CS serves as a terminal for CellScales. Its response to key presses may be delayed due

to transmission times. The 3750CS will on occasion, display a “WAIT” message while transacting

setups and scale controls.

RF NETWORK SETUP

The 3750CS is a RF Modem connected device. The RF Modem requires setup to connect to one or

more CellScales.

RF NETWORK

Sets the primary network number. Set this numbers to match the Network number of the CellScale master the

3750CS is associated with most often. Ranges from 0 to 31.

C/S ID

Sets the primary master CellScale ID number. This number must match the Source Address number of the

primary master CellScale. Ranges from 0 to 254.

MY ID

Each slave unit in a given Network must have a unique ID number. Enter up to three digits to designate the

3750CS ID number. Ranges from 0 to 254.

TIMEOUT

Sets the time in seconds (0-1800) that the 3750CS will wait for data from the CellScale. The display will

blank out if no data is received within this time period. Defaults to 10 seconds. Entering 0 turns off the

Time-out timer. MSI recommends at least a 5 second timeout period to handle small lapses in transmissions.

The system defaults to 10 seconds.

ENERGY

Sets the RF power level between 10mW (Low), and 100mW (High). In most applications power should be

set to High. Reduced energy can reduce the size of the coverage/interference zone which may be desirable for

multiple-network applications. Always check for adequate range coverage when using the Low setting.

Summary of Contents for CellScale 3750CS































































































Search results

Summary of Contents for CellScale 3750CS

Reviews:

Related manuals for CellScale 3750CS

Brands by name

Popular brands

MSI CellScale 3750CS, User Manual

Search results

Summary of Contents for CellScale 3750CS

Reviews:

Related manuals for CellScale 3750CS

Brands by name

Popular brands