MSI CellScale 3750CS User Manual Download Page 14

Page: 14 / 94

Page 14 MSI-3750CS RF Weighmeter • User Guide

3750CS

ELL

CALE RF DIGITAL WEIGHT INDICATOR

Range is Inadequate

Antenna placement is the most common cause of poor range. Check that the RF power level of the master

and slave units is on “High”. Radio signals in nearby bands that have significant power can also reduce range.

Longest range will always be achieved by Line-of-sight antenna placement. Any obstacle that interferes with

LOS will reduce the range. Particularly bad blocking is caused by metal buildings, solid concrete walls, and

anything else that has fairly high electrical conductance. Raising the antennas higher can help. Sometimes just

moving the antennas sideways will find an RF “path” that will improve distance. The CellScale can sometimes

take advantage of reflecting surfaces to get around obstacles. Antennas should always be place in vertical

polarization, that is the shaft of the antenna should be perpendicular to the earth, not parallel. It is OK to mount

the Antenna upside down. This is a good solution when an antenna is mounted on the ceiling for communication

with CellScale components in the building.

Summary of Contents for CellScale 3750CS































































































Search results

Summary of Contents for CellScale 3750CS

Reviews:

Related manuals for CellScale 3750CS

Brands by name

Popular brands

MSI CellScale 3750CS, User Manual

Search results

Summary of Contents for CellScale 3750CS

Reviews:

Related manuals for CellScale 3750CS

Brands by name

Popular brands