Moulinex MASTERCHEF GOURMET HF80C, Manual

Page: 8 / 31

11
maker.
• Do not use the pasta maker for more
than 15 minutes continuously. Allow the
appliance to rest for 1 hour before
using it again.
• To prevent the pasta from sticking
together after being cut, you can lightly
sprinkle with flour or extra-fine semolina
as it leaves the disc, just before cutting
it with the pasta cutter.
• The first batch of pasta coming out of
the discs may be deformed. You can
cut off the first few centimetres, form
small balls again and insert them
through the feed tube of the pasta
maker.
• Fresh pasta can be cooked
immediately in a large volume of
boiling salted water. The cooking time
depends on the shape and thickness
of the pasta. Cook the pasta until it is
"al dente" (slightly firm to the bite).
• Storing fresh pasta: Allow it to dry in the
open air for 1 hour by spreading it in a
single layer on a clean tea towel. Then
place it in an airtight bag or container.
You can store it for 5 days maximum in
the refrigerator.
•Attention: do not leave the fresh
pasta to dry for more than 1 hour at
room temperature as it contains
fresh egg. After 1 hour at room
temperature store pasta in a
refrigerator to avoid any food safety
risks.
• You can store the 5 discs in the storage
base (I7) ; the sixth disc can remain
assembled on the pasta maker during
storage.
2 - MAKING COULIS
ACCESSORIES USED:
- Attachment holder (E)
- Coulis attachment (J)
- Tray (F8)
- Pusher (F7)
2.1 - FITTING THE ATTACHMENT
• Press the button (a2) to release the
multi-function head (a3) and raise it
until it locks in place.
• Place the attachment (e) and lock it in
the anti-clockwise direction such that
the outlet is in alignment with the
appliance.
• Place the multi-function head (a3) in
the horizontal position by pressing the
button
(a2) once again.
2.2 - ASSEMBLING THE COULIS
ATTACHMENT
Hold the feed screw (J3) and insert the
drive (J2) (spring facing the screw).
Insert the assembly into the widest hole
in the plastic body
(J1) . Turn the whole
assembly, the screw facing upwards, and
fit the filter
(J4) aligning the 2 lugs with
the 2 notches in the plastic body (J1) .
Position the ring nut (J5) and screw
home.
2.3 - FITTING THE COULIS ATTACHMENT
ON THE APPLIANCE
• Facing the attachment holder (E)
outlet, insert the assembled coulis
attachment
(J) , with the feed tube in
the plastic body (J1) inclined to the
right, aligning the two bayonets in the
plastic body
(J1) with the two
notches in the attachment holder.
Push the coulis attachment home into
the attachment holder and turn the
coulis attachment anti-clockwise until
10
in the horizontal position by
pressing the button
(a2) once
again.
➢
ASSEMBLING THE PASTA MAKER
• Hold the plastic body (I2) by the
feed tube.
• Insert the feed screw (I3) (long
shaft first) into the plastic body
(I2) .
• Position the desired disc (I4) on
the feed screw (I3) aligning the 4
small lugs with the 4 notches in the
plastic body
(I2) .
• Screw the ring nut (I5) onto the
plastic body (I2) in the clockwise
direction, without locking it. Do not
use the spanner (I8) to lock the
nut.
• Insert the pasta cutter (I6) in its
housing on the left of the plastic
body
(I2) , aligning its lug with the
corresponding hole in the plastic
body, push it until it locks in place
and push it down towards the disc.
➢
FITTING THE PASTA MAKER ON THE
APPLIANCE
• Facing the attachment holder (E)
outlet, insert the assembled pasta
maker inclined to the right, aligning
the two bayonets in the pasta
maker with the two notches in the
attachment.
• Push the pasta maker home into
the attachment and turn the pasta
maker anti-clockwise until it latches
with the feed tube in the vertical
position.
➢
USAGE, DISMANTLING AND TIPS
• Make sure that the safety cover
(a5) is locked correctly (clockwise)
on the high-speed outlet (a4) .
• Place a container to collect the
pasta in front of the appliance.
• Run the appliance by turning the
selector (a1) to speed "4" .
• Insert a small ball of dough
through the feed tube. Wait for the
feed screw to be visible before you
insert the next dough ball.
Never
push the dough down the feed
tube with your fingers or any
other utensil.
You can use the
spanner/pusher handle (I8) to
insert the dough again, only if the
dough is stuck inside the feed tube
and is not driven directly by the
screw.
• Use the pasta cutter (I6) by
rotating it to cut the pasta to the
desired length.
• Allow the pasta maker to run until
there is no more dough to extrude.
To stop the appliance, turn the
selector to "0" speed and wait for
the appliance to come to
a
complete stop.
Dismantling :
• Unlock and dismantle the pasta
maker in the reverse order of the
assembly.
You can use the
spanner/pusher (I8) to unscrew the
ring nut (I5) .
Tips :
• If the prepared dough is too wet or too
sticky to be fed through the pasta
maker, just sprinkle it with a little flour
to obtain the desired consistency
before feeding it through the pasta
maker.
• On the contrary, if the dough is too dry,
add a little beaten egg and mix again
before feeding it through the pasta
NOTICE_PASTA_BOX_0828670-02_PASTA BOX 22/03/12 10:58 Page10